MENU     Set Up     Blinking Back the Code     Redefining a Key
Volume Punch Through     Volume Default     Clearing Out
Key Mover     Scan
Programming your One For All remote

How to Program your One For All® remote

( URC-2060, URC-2062)


Set Up

After getting the proper codes from your manual or Customer Service, use the following instructions to enter them into your remote.

  1. Press the device you want to program, then release.
  2. Press and hold the Magic button until the red LED flashes twice, then release.
  3. Enter your 3 digit code.
  4. You should receive 2 quick flashes after entering your code.

menu

Blinking Back the Code:

  1. Tap the device Key - Release
  2. Hold "Magic" until it blinks twice - release.
  3. Press 9 - 9 - 0.
  4. Press 1, Count the number of blinks. (1st digit)
  5. Press 2, Count the number of blinks. (2nd digit)
  6. Press 3, Count the number of blinks. (3rd digit)
If the remote DOES NOT blink it means the number is 0.

menu

Redefining a Key

  1. Hold "Magic" Until it blinks twice.
  2. press 9 - 9 - 2.
  3. press the DEVICE key you want moved
  4. press the DEVICE key you want to replace.
Example: If you want the Aux key to be a TV key:
"MAGIC" (2 blinks) 9 - 9 - 2, TV (you want to move TV)
Then AUX (you want to replace AUX).

menu

Volume Punch Through

This sets Volume to work for one device in all modes.
For example, the TV volume will work in the cable and VCR modes.
  1. Hold "MAGIC" until it blinks twice - release.
  2. Press 9 - 9 - 3.
  3. Press the device key you would like the volume to come from.
You will get two blinks on the remote.
If you want to set the volume for a device to work just one or two other devices-- refer to the instructions under "KEYMOVER-From one button to another"

menu

Volume Default

Use this to get Cable or VCR volume to work.
  1. Hold Magic until it blinks twice - release.
  2. Press 9 - 9 - 3
  3. press the VOLUME+ key, you will get two blinks.
Now The volume is set for all original devices.

menu

Clearing Out

A Device Key - Or Another Button

  1. Tap the device Key - release.
  2. Hold Magic for Two blinks - release.
  3. Press 9 - 9 - 2
  4. Press the button twice. - Two blinks.

All Key movers, and Defaults

  1. Tap the device Key - release
  2. Hold "Magic" for two blinks - release
  3. Press 9 - 8 - 0 -- Two blinks.

menu

Key Mover

An Extended Function To A Button

  1. Tap the DEVICE key - Release.
  2. Hold "Magic" for two blinks - release.
  3. Press 9 - 9 - 4.
  4. Tap the "Magic" button and then the three digit extended function.
  5. Tap the button you wish to use for that function - Two Blinks.

From One Button to Another

  1. Hold "Magic" until it blinks twice - release.
  2. Press 9 - 9 - 4.
  3. Tap the DEVICE and the FROM button
  4. Tap the DEVICE and the TO button
  5. Two Blinks
EXAMPLE: To take the volume from a TV and put it in the VCR mode,
it would be: MAGIC - 9 - 9 - 4 - TV - VOL UP - VCR - VOL UP - two blinks.
You would have to do the same process for VOL DN and MUTE.

menu

Scan

Your remote may have a "SCAN" button on it. If it does you will use the following procedure to scan channels on your TV or VCR.
  1. Press the Device key you want to scan.
  2. Aim your remote at the device and press the SCAN button.
    Your remote will scan through all of the channels stopping at each one for 3 seconds.
  3. To stop scanning, simply press any other key.
      Remember you have to aim the remote at your device the entire time you are using SCAN.

      menu


HOME
All Material Copyright Universal Electronics Inc.
"One For All" copyright Universal Electronics Inc.
Any questions about the products should be directed to help@ueic.com